State of H1:

• EY: vented, first contact applied
• MY: bake continues
• CS:
  • HAM6/SQZ:
    • in-chamber work at HAM6 is complete, or close to complete
    • ISCT6 is sitting on the North side of the chamber and is wired up
    • the SQZ table is on the South side of the chamber and is being commissioned
  • TCSX: the laser was turned on today
• MX: card access work continued today
• EX: Pcal baffle work
• all optics aligned, except ETMX and TMSX which are damped
• all SEI platforms that aren't locked are in damped or states above damped (robust_isolated)
• SEI config is in Large EQ NOBRSXY

Activity Detail:

• 09-03-18 15:12 Marm and Mark craning the lift over the beam tube in LVEA, under 500lbs
• 09-03-18 16:31 Fil to EY to work on access system
• 09-03-18 16:35 Mark to EY to get the snorkle lift and bring back to the CS
• 09-03-18 17:07 Mark to CER and LVEA to trace a cable
• 09-03-18 17:16 Mark is done moving the snorklelift
• 09-03-18 17:30 APS is at MX
• 09-03-18 17:37 Jim, Marer, Niko, Corey, to EX for Pcal baffle install
• 09-03-18 17:58 Ken to EY to remove equipment from the outside of the building
• 09-03-18 18:10 Ken back from EY
• 09-03-18 18:21 Matt to LVEA to look for iLigo TCS lasers
• 09-03-18 18:22 Travis and Betsy to EY for first contact
• 09-03-18 18:26 Terry to HAM6 SQZ table
• 09-03-18 18:29 Peter to TCS chillers to check hi and low setpoints
• 09-03-18 18:32 Fil is done ay EY and is now at MX
• 09-03-18 18:43 Chandra to MY
• 09-03-18 18:44 Karen to MY
• 09-03-18 18:44 Matt is back from the LVEA
• 09-03-18 18:50 Karen leaving MY
• 09-03-18 19:14 Fil done at MX now at MY
• 09-03-18 19:32 Mark done installing table over HEPI peer on North side of HAM6
• 09-03-18 19:32 Chandra to LVEA to spin up the Y beam manifold pump
• 09-03-18 19:46 Richard back from outbuildings
• 09-03-18 20:04 Ed and Jason out of PSL for lunch
• 09-03-18 20:16 Liz going to outbuildings for access control work
• 09-03-18 20:25 Pcal crew back from EX
• 09-03-18 20:37 Betsy and Travis to EY
• 09-03-18 20:38 Nutsinee to HAM6
• 09-03-18 20:48 Fil and Liz to MY
• 09-03-18 20:58 TVo and Olivia to LVEA to turn on a CO2 laser
• 09-03-18 21:14 TVo and Olivia back from LVEA, TCSY laser was turned on
• 09-03-18 21:18 JeffB to LVEA to reset Dust5
• 09-03-18 22:10 JeffB to EX to reset dust monitor
• 09-03-18 22:19 Nutsinee to HAM6
• 09-03-18 22:26 EY temperature has been giving alarms since 22:00 for high temperature
• 09-03-18 22:27 Bubba took a look and the temperature has leveled out at about 66F
• 09-03-18 22:27 EY setpoint is 65F so temperatures there should be coming down
• 09-03-18 22:56 Travis and Betsy back from EY
• 09-03-18 22:56 Fil and Liz at EY
• 09-03-18 23:03 Ed and Jason to PSL enclosure
• 09-03-18 23:07 Mark to Cosmic Ray detector in LVEA and CER
• 09-03-18 23:22 Mark done in LVEA
• 09-03-18 23:35 FIl and Liz back from EY and all other outbuildings